Skip to content
Home » Xfinity Bridge Mode No Internet Solved!

Xfinity Bridge Mode No Internet Solved!

When the Xfinity router comes with a bridge mode setting, it can increase your Wi-Fi network’s range by using two of them at once. But recently some users like me felt a horrible experience of not getting a solid wifi signal. Xfinity bridge mode no internet issue can give serious troubles! You’ll find many different guides on resolving the issue about the Xfinity Bridge Mode having no internet. But, most of these are generic guides that are done across all routers.

Xfinity bridge mode no internet issue is serious trouble! You can find many different guides on how to resolve the problem about X1’s Bridge Mode lacking an active connection. However, most of these work for all routers – which isn’t really helpful since each router requires its own specific solution and not simply clicking “next” until you get results that will take care of your living room or office space adequately.

If you are having trouble with your Xfinity router while it’s in Bridge Mode, make sure that the device is configured correctly and check to see if any cables need replacing. You can try disabling bridge mode on one of these routers before resetting back upright as a factory default setting.

Let’s dive in to the solution

What is Xfinity Bridge Mode & Benefits Of Using It?

Bridge mode is a feature that can be found on some Xfinity routers. When this setting is enabled, it allows the router to act as an extension of your existing Wi-Fi network. This means that you can use two routers at the same time to extend the range of your signal. It’s a great way to fix Wi-Fi dead zones in your home.

Bridge mode lets you connect two routers without the risk of performance issues. Unlike traditional Wi-Fi repeaters, bridge mode breaks the network into two separate segments with only one device per segment (each router has its own IP subnet). This prevents the routers from fighting over the same bandwidth and eliminates any potential slowdown that could occur.

Bridge mode is perfect for situations where you need to provide Wi-Fi coverage in a large area, like a detached garage or workshop. It can also be used to create a guest network that’s separate from your main network.

Fixed Xfinity Bridge Mode No Internet

Check for Xfinity Outages

It’s probably the first reason of not getting internet while Xfinity is in bridge mode.

When you’re troubleshooting a networking problem, it’s important to ensure that your connection is stable and connected before spending too much time on the issue.

To check the reliability of your network contact Xfinity support and ask them if there are any network outages or scheduled maintenance in your area.

Make Sure That Bridge Mode is Enabled on Your Router

Another reason for not having internet while in bridge mode is that the routers are not set up to use bridge mode.

To enable bridge mode on your router, you will need to access the administrative console. For more information on how to do this, please check your router’s manual or contact Xfinity support. You can also check below

  1. Access your Xfinity router’s admin tool
  2. Login by typing your username and password
  3. Select ‘Gateway’ tab > At a Glance’
  4. Find the Bridge Mode option, as well as the buttons next to it that say “Enable” and “Disable.”
  5. Once you have enabled bridge mode, your routers will need to be physically connected together with an Ethernet cable.
  6. Done

Check Your Ethernet Cable and Connection

Another common reason for not having internet while in bridge mode is a faulty Ethernet connection.

To troubleshoot this, you will need to ensure that the routers are properly connected with an Ethernet cable.

You can also check the cable to make sure it is not damaged.

When there is a bad ethernet connection between the two routers, it will make communication difficult for devices on your network. This can lead to issues with accessing internet service or even causing other problems like unable to print wirelessly at home due to an inadequate wireless signal strength from router placement in close proximity of printer model which requires Ethernet cable plugged into its port needing a continuous power supply.

Disable and Enable Bridge Mode

If the previous steps do not work, try disabling bridge mode and then enabling it again.

To disable bridge mode on your first router:

Log in by typing your username and password > Select ‘Gateway’ tab > At a Glance” > Find Bridge Mode option as well as buttons next to it that say “Enable” or “Disable.”

Clicking either will change what state they are currently in with respect to whether this function has been enabled yet (either true/false depending upon if the button says enable). Once you have disabled bridge mode, wait for ten seconds before re-enabling it again. If this does not fix the issue, move on to the next step below.

Factory Reset Your Router

If disabling and then enabling bridge mode does not work, you may need to factory reset your router.

To do this, you will need to access the administrative console and find the Factory Reset option. Check below where I explained step by step how to reset a router:

  • First, you will need to access the administrative console. This can be done by opening a web browser and typing in the IP address of the router. By default, this is 192.168.0.254 for Linksys routers.
  • Next, click on the Maintenance tab and then select Factory Reset.
  • You will then be asked to enter the password for your router.
  • After that, click on OK and wait a few minutes until the process is complete.
  • Your router will turn off automatically then restart itself with factory settings enabled.

How to reset the router manually?

  • Find the WPS/Reset button at the back or bottom of your router and press it with a pin until all lights on the front blink.
  • Wait for 20 seconds .
  • Unplug the router from the power source and wait for 20 seconds.
  • Plug it back in to its power source.
  • Wait until all lights on your router turn green again.
  • Done

Finally, Contact Xfinity Support 

If all of the steps failed to work that means there is something fishy weather with your Xfinity router or internet connection. That’s why it’s better to contact Xfinity customer support where they will guide you in the straight direction on how to manage and go through this situation. Also, technical support is always available for consumers from Xfinity.

FAQs

Does bridge disable the Internet?

Bridge mode turns off the router functionality of the modem (including built in WiFi), and is often used to allow a second networking device (i.e. a separate WiFi router) to pull a public IP address when connected to the modem. … It does not disable your Internet connection however it disables your Xfinity wireless gateway functionality

How do I turn off bridge mode without Internet?

Removing the ethernet cable can cause disconnect your router from bridge mode. NOTE: Enabling or disabling bridge mode only affects the coaxial port. You can use Ethernet or WiFi in either bridged or non-bridged modes.

What are the disadvantages of bridge mode?

The main downside of bridge mode is that you lose your Xfinity wireless gateway’s features, such as the ability to use a public IP address and its firewall. Additionally, if there are devices on your network that need to go through the Xfinity wireless gateway (like an Xbox One), they will no longer be able to connect once you put the modem into bridge mode.

How do I get my Xfinity modem out of bridge mode?

Log in to the Comcast router and go to Gateway > Connection > IP Configuration. Set IPvMode to DHCP (or “IPvMode” : “DHCP”). Click Save Settings, wait a minute or two, and then turn the router off and on again.

When should I use bridge mode?

Bridge Mode is only needed when encountering specific cases of Double NAT. For most people, Double NAT does not affect Wi-Fi performance. However, it can be an issue if you play online games or use IP address assignments, port forwarding rules, or DMZ hosting on your router. In these cases, you can put the modem into bridge mode to eliminate Double NAT and improve Wi-Fi performance.

Does bridge mode improve speed?

Bridge mode will not improve the speed of your Internet connection. It will only disable the wireless gateway features of the modem.

What is the difference between bridge mode and repeater mode?

AP mode allows the device to be used for wireless networking. Repeater mode extends the range of your Wi-Fi signal, however, it will also slow down the speed of your network. Bridge mode turns off the router functionality of the modem (including built-in WiFi), and is often used to allow a second networking device (i.e. a separate WiFi router) to pull a public IP address when connected to the modem.

Conclusion

The most common problem with Xfinity routers is that they are in Bridge Mode and not routing traffic properly. You can fix this by making sure your internet connection works, checking the cables for any problems or disconnects between devices (router/modem), and disabling bridge mode on one of them until you get an answer as to which setting needs to be corrected first, or if everything failed to solve it then the only problem is contacting support for further process. We would suggest you use your Xfinity router in normal mode until the problem gets solved.

Read More